DIN 50190 PDF


DIN Hardness depth of heat-treated parts; determination of the effective depth of hardening after nitriding. standard by Deutsches. DIN – Draft standard [WITHDRAWN] DIN – Draft. Heat treatment of ferrous materials; terms. from EUR VAT. Standard [WITHDRAWN] DIN Hardness depth of heat-treated parts – Determination of the effective depth of carburized and.

Author: Zuran Vular
Country: Maldives
Language: English (Spanish)
Genre: Medical
Published (Last): 10 April 2017
Pages: 489
PDF File Size: 16.80 Mb
ePub File Size: 4.68 Mb
ISBN: 627-5-23857-412-6
Downloads: 62632
Price: Free* [*Free Regsitration Required]
Uploader: Shaktijora

Different materials like plastics, metals, coatings and ceramics can be tested.

GWP: Hardness test

A determination 5010 the hardniss is carried out, depending on the selected test load, on the by plastic deformation caused dent by average calculation of the diagonal. Furthermore it offers 501190 possibility to determine values, which are equivalent compared to the traditional methods.

Vickers, Rockwell and Brinell. The Rockwell method is preferably used for very hard materials or heat treatment conditions, e. The Brinell hardness test is used for soft to medium hard metals, and very porous and inhomogeneous materials such as cast or light metal alloys.

Our according to DIN EN ISO accredited lab offers the usual stationary methods of hardness testing, which are used in the field of metallic materials: For the examination next to metallographic investigations also hardness profiles are used.

Starting from very soft non-ferrous metals such as Pb or Cu, over surface layer hardened steels up to very hard coatings such as tungsten carbide. Dni to different hardness and processing methods the testing methods can be differed: Thermal and mechanical stress can induce microstructural changes in materials, which can be detected with a hardness test.


By these small impressions also very close contiguous impressions can be realized e. Filling the sample with 5090 hardness mapping can be useful for case-hardened parts or to check sample homogeneity. With the micro hardness test usually load ranges of 1 to g e.

The instrumented penetration testing for the determination of hardness and other material parameter also universal hardness or hardness martens also offers the possibility to determine and estimate the elastic distortion of materials in contrast to the classical methods like Rockwell and Vickers. Because of this kind of determination the hardness value can be read from a scale without optical measurement devices and the requirements regarding surface quality are lower.

Instrumented penetration testing universal hardness test.

Surface layer hardenings are common methods for improving the wear resistance of components. Hardness mapping are performed according to Vickers. Also in the field of damage investigation hardness profile measurements are used, to e. Usually the examinations take place on metallographic prepared samples.

Hardness test

For the characterization of different materials the hardness test offers a very wide spectrum of possibilities. These evaluations lead to conclusions about e. Similar to the Vickers method the calculation of the hardness is based on the ratio of the average diagonal diameter for the used ball and the test load.

Hereby a pyramidal diamond indenter is pressed with a defined stress in the workpiece. The software automatically assigns colors for the minimum and maximum hardness values. Via these measurements next to the hardness difference compared to the core hardness also the depth can be determined.


Hardness mapping are often applied to verify welded joints. These apply to the expected hardness, ball diameter and test load.

Particularly in the case of multi-layered welds, it is thus possible to identify specific areas, in which the heat input has significantly affected the microstructure, and as consequence affects the quality of the weld joint.

The GWP is equipped with the most modern hardness test devices, which offer the possibilities of manual, semiautomatic and fully automatic evaluation. For this purpose several Vickers-test indentations are set and measured in defined intervals to the component edge.

Home Lab Services Material testing Hardness test. In contrast to the Vickers and Brinell method, the hardness is determined not by the lasting dent diagonal but by the depth of penetration. Hardness test with metals. Thus, the hardness is an essential ingredient of component calculations, drawing specifications or in the characterization of materials.

In the tests hard metal balls with different diameters 1, 2.

The GWP covers with their equipment park the typical testing areas. This feature is used to detect even the smallest local hardness increase in large samples. Modern metal materials offer a very wide range di different operation purposes. From the hardness test procedures, the Vickers method is the most universally applicable test.